프로젝트 설명

정밀전천일사계

Pyranometer MS-80

일사계, 일사량, 일사, 일사량측정기, 전천일사계, 수평일사계, 기상관측, 태양광

ISO 9060 기준 Class A / Secondary Standard Class(부기준)

세계 최고급 사양 일사계 출시

5년 제품보증 일사량 측정기 출시

MS-80 시리즈는 ISO9060의 Class A / Secondary Standard Class(부기준) 에 부합하는 세계 최고 사양의 전천일사계입니다.

Features

  • ISO 9060 Class A / Secondary Standard class(부기준)
  • Fastest detector response
  • lowest temperature coefficient
  • Lowest offsets A and B
  • Industrial sensor outputs
  • 5 years warranty and recommended recalibration

기능

  • ISO 9060 기준 Class A / Secondary Standard Class(부기준)
  • Fastest 탐지기 반응
  • lowest 온도 계수
  • Lowest 오프셋 A와 B
  • Industrial 센서 출력
  • 5년 보증 및 권장 재교정.

제품특징

감도 변화 : 0.5 % / 5년 제품보증
MS-80은 기존 일사계와 다르게 써머더미(열전)가 햇볕에 노출되지 않는 디자인으로 설계 되었습니다.
따라서 자외선이나 습도의 영향이 매우 작기 때문에 장기 안정성이 매우 우수합니다.

제품 보증 5년, 재 교정 권장 기간 5년
장기 안정성과 기밀성의 향상으로 보증 기간 5년, 건조제 교체가 필요 없는 보증 기간 입니다.

현격한 차이의 고속 응답성 : 0.5초 이하 (95 %) / 1.0초 이하 (99 %)
고속 응답의 최신 써머더미 기술을 채용하는 것으로 응답 시간 0.5초 (95% 응답)를 실현하고
시시각각 변화하는 일사 강도의 측정에 적합 합니다.

제로 오프셋 개선
기존 모델에 비해 돔 표면적이 20%로 작기 때문에 열 영향이 적고 외기 온도 변화의 영향을 받지 않는 일사량계 입니다.

인터페이스의 확장
각종 인터페이스에 대응 할 수 있도록 2개의 모델을 준비하고 있습니다.
MS-80 : 직류 mV 출력
MS-80S : Modus 485 RTU / 4-20mA / SDI-12)

팬 히터 유닛
옵션의 팬 난방 장치를 이용하여 추운 지역에서 강설 등의 영향을 줄일 수 있습니다.

EKO’s new generation sensors broke with the rules of traditional pyranometer architecture. The innovative patented design was inspired by the combination of latest technologies and state-of-the-art thermopile sensor, enabling a breakthrough in unprecedented low zero-offset behaviour and fast sensor response.
The compact sensor with single dome is immune to offsets and integrates all value added functions such as a ventilator, heater and different industrial interfaces.
The MS-80S is built in MODBUS 485 RTU, 4-20mA and SDI-16 converter are compatible to the industrial output standards. Due to the ultra low temperature dependency and exceptional non-linearity characteristics, the converter guarantees an optimal sensor performance, under any environmental conditions.
The MS-80 pyranometers are manufactured in a consistent way followed by strict quality inspection and performance evaluation. For each sensor the directional response and temperature dependency are measured and validated through a measurement report that comes with the sensor. EKO provides a unique calibration compliant to the international standards defined by ISO/IEC17025 / 9847.
The sensor has 5 years warranty, 5 years recommended re-calibration interval and no longer need to change the dessicant.

Specifications

Specifications (typical) MS-80 MS-80S
01. Output mV Modbus 485 RTU,
4-20mA, SDI-12
02. ISO 9060 classification Class A / Secondary Standard Class(부기준)
03. Response time 95% (sec) < 0.5
04. Zero offset – Thermal radiation (200W/m²) +/- 1 W/m²
05. Zero offset – Temperature change (5K/hr) +/- 1 W/m²
06. Non-stability (change/5years) +/- 0.5 %
07. Non-linearity (at 1000W/m²) +/- 0.2 %
08. Directional response (at 1000W/m²) +/- 10 W/m²
09. Spectral selectivity (0.35-1.5µm) +/- 3 %
10. Temp. response (-10 to +40°C) +/- 1 % +/- 0.5 %
11. Temp. response (-20 to +50°C) +/- 1 % +/- 0.5 %
12. Tilt response (at 1000W/m²) +/- 0.2 %
13. Sensitivity (µV/W/m²) Approx. 10
14. Impedance (Ω) Approx. 45kΩ
15. Operating temperature range (°C) – 40 to +80
16. Irradiance range (W/m²) 0 – 4000
17. Cable length 10m
18. Wavelength range in nm 285 to 3000
19. Ingress protection IP 67